Danbo merk PIN TIMES
terbuat dari bahan karton tebal
selalu terlihat bagus untuk photography
Danbo pin times [DIY set, 4 pcs], ini adalah set Danbo yang terdiri dari 4 buah Danbo yang belum di rakit. Anda perlu merakit Danbo nya itu sendiri. Danbo yang di rakit bisa di gerakkan tangan dan kaki nya. Jadi bagi anda yang suka sama photography, maka ini adalah point plus dari produk ini.
Apakah Danbo?
DANBO adalah kependekan dari Danboard, dibuat dari kertas karton board (bukan plastik). Boneka ini adalah kreasi dari Azuma Kiyohiko seorang komikus serial manga Yotsuba. Bentuk boneka ini sangat unik, yaitu action figure dengan penampilan seperti manusia, mainan ini sangat sederhana bentuknya, kotak mulai dari kepala, lengan, pinggang, hingga kaki. Kedua mata kecil dengan bibir segitiga. Namun dia dapat bergaya di depan kamera.Bagaimana tidak DANBO dapat digerakkan secara manual dan dibentuk dengan berbagai macam gaya unik. Perusahaan yang membuatnya menggunakan teknologi tinggi di setiap persendian boneka ini sehingga membuatnya mampu bergerak luwes. Ekspresi dari si kardus imut ini menjadi daya tarik utama…. Buruan dapatkan Danboard versi Pin Times imut ini untuk menambah koleksi Anda.
Info Produk
Bahan : karton tebal
Isi
4x Danbo yang belum jadi
*Tidak ada buku intruksi dan lem untuk paket yang satu ini.
Dimensi
Tinggi : 8cm
Rp. 100.000
Ketersediaan: readystock
Penerjemahan dalam bahasa English
1.Details panels
1. hands box
2. the first box
3. body
4. legs
5. the base station
6. small box internal support
7. head sticker
8. hands sticker
9. legs box stickers
10. body stickers
11. Exercise with plates
12. joint use of scroll
13. joints with plates ABC
14. joints with plates
15. articular plates with stickers
2: Plates cut
Description: cut down all the plate. Plate quiet small , if scissors feels not good to use you can use cutter and ruler for better results.Within the box panels missing cut It does not matter, the latter can be cover stick. Cutting plate is very important, in order to ensure that products has a nice straight cut. joint production of more elaborate pieces can be cut later on.
Note: plate 3 to the top of the red part of the body, cutting it when the first cut to make the perfect post-assembly
3: Plates origami
Note: the box with two support pieces need to fold. Do paper folding one time, must not repeat the folding. within thebody 4 support can be no break, later for stick use plates.
Description: The front line can be folded over with a ruler, which can guarantee a place.
4: plates paste
Description: use paper glue, be patient, and preferably make with the sunlight (faster dry)
5: Joint Production
Make a strip-purpose become roll with glue, can not see the white is just right for a 3 mm round
ABC cut to a good backup joint
ABC stick together , joint B at above, joint C in below
A hole will be glued to the joint top of B become T-shaped form.
put a few glue in T-joint holes and stick the scroll together, wait until the glue dry
make T-joint horizontal and cut leave about 6mm After u cut down the T-joint, fold inward until wings form. Do another scroll cut for 6mm and put glue in the joints at both ends of pieces
Glued joints result as picture above, one danboard need to do a cardboard box joint 5 pieces
Joint D and E will cut a good alternative joint
Tear off E the adhesive joint , will be glued joints D black face down in the middle of the joint E, (see picture)
Stick a scroll attached to the E side of the joint
E joints and then through the middle of a good joint to go, as shown above
The other end of the joint E bend over, remember to stick hard this joints
Scroll cut off the excess, leaving about 7 mm
6: Other parts production
The base 1,2,3,4 from top to bottom to glue the holes aligned, then insert with the vertical scroll bar
The first part of the joint support shown above plugged
7: Stick
After the plates cut posted in accordance with their distribution, including the box,
Note: the black side of the arms and legs do not stick, stick only affixed to the body finished 4 support all look inside and outside the fold.
After the body attached to the parallel support legs stuck inside the body, even if you’re done, you can start assembling
8:Finishing
Assemble all the parts all together lovely DANBOARD small box to stand in front of you
No comments:
Post a Comment